All Grain Batch 2 – English IPA with Chinook and Hallertau

It’s time for my second batch of all-grain beer.  This one will be an English IPA using chinook and hallertau hops.  Here’s the ingredient list:

  • 6 lbs 6-row pale malt
  • 12 oz cara-amber
  • 8 oz amber malt
  • 8 oz caramel wheat malt
  • 0.5 oz chinook 13.9%AA at 60 minutes
  • 1 oz hallertau 3.9%AA at 15 minutes
  • 1 oz hallertau 3.9%AA at 8 minutes
  • 1 oz hallertau 3.9%AA at 0 minutes
  • 2 oz hallertau 3.9%AA dry hop
  • Wyeast 1275 Thames Valley Ale Yeast

Procedure:

  1. prepare checklist
  2. lay out ingredients and equipment
  3. Add grains to mash tun
  4. bring 3 gallon spring water to 168 F
  5. Add 2 1/4 gallons of 168F spring water to mash tun on top of grains, then stir well
  6. continue to heat the remaining water to near boil
  7. measure temperature after temperature equalizes in mash
  8. adjust mash temperature using either heated mash water or cool spring water as needed to reach 155F
  9. mash for 1 hour minutes at 155F
  10. during mash, bring another 3 gallons of spring water to 172F
  11. during mash, stir about every 15 minutes or so, checking temperature and adjusting if needed
  12. at end of mash, begin draining wort into pitcher
  13. allow first runnings to drain into a pitcher until clear
  14. pour first runnings back on top of mash
  15. drain remaining wort into boil pot until mash tun is near empty
  16. add 1.5 gallons 172F water (adjusted as needed)
  17. stir well
  18. drain first runnings of first batch sparge into pitcher until clear (or close to it)
  19. pour first runnings of first batch sparge back on top of mash
  20. drain wort into main boil pot until near empty
  21. add another 1.5 gallons 172F water to mash tun (adjusted as needed)
  22. stir well
  23. drain first runnings of second batch sparge to pitcher until clear (or close to it)
  24. add first runnings back into mash tun
  25. drain wort into main boil pot
  26. add wort chiller to boil pot, filled with hot water
  27. bring main boil pot to a boil
  28. when boil is reached, add bittering hops, 0.5 oz chinook at 60 minutes
  29. at 30 minutes, add about 1/4 tsp Wyeast nutrient blend to a small amount of spring water and dissolve
  30. add nutrient blend at 15 minute mark
  31. add 1/8 tsp Irish moss powder at 15 minute mark
  32. add 1 oz hallertau at 15 minutes
  33. add 1 oz hallertau at 8 minutes
  34. add 1 oz hallertau at 0 minutes
  35. hop stand for 10 minutes
  36. at flameout, turn on water for wort chiller
  37. begin sanitation procedures on spoon, thermometer, bucket, wine thief
  38. stir occasionally with sanitized stainless spoon during cooling
  39. ensure bucket, wine thief, thermometer, strainer, spoon are sanitized
  40. when wort gets to about 72F, add to fermentation bucket, pouring through sanitized strainer to catch any extra solids and to help aerate
  41. take OG reading with sanitized wine thief
  42. thoroughly aerate wort with sanitized stainless steel spoon again
  43. ensure wort is 72F or a little less before pitching yeast
  44. ensure yeast is a little cooler than wort before pitching
  45. pitch yeast
  46. gently stir using sanitized stainless steel spoon
  47. install sanitized bucket lid and airlock
  48. ferment in closet for 14 days at 67F ambient air temp.
  49. after 14 days, add dry hops, 2 oz hallertau
  50. ferment a total of 21 days
  51. take FG sample and bottle
  52. use 3.5 oz corn sugar at bottling

Targets:

  • OG  1.056
  • FG 1.014
  • SRM 11.5
  • IBU 55.9
  • ABV 5.5%

Actual OG: 1.046 (a little low)

Actual FG: 1.012

Notes: only yielded 2.5 gallons of usable beer due to excessive trub (no doubt from spilling during the transfer from kettle to bucket).

Advertisements
Post a comment or leave a trackback: Trackback URL.

Comments

  • alcaponejunior  On October 7, 2012 at 8:29 am

    Well I realize this post was made about two weeks ago, but I’m just getting around to actually brewing it today. That’s how it goes! I’ve got some homebrews in the fridge to help me on my way 🙂

  • alcaponejunior  On October 7, 2012 at 12:58 pm

    Just finished the batch sparging. Boil will be about 4+ gallons. I used a little more water in the batch sparging process this time, and thus did not need to use any top-off water at all. I should hit the target volume within a couple of tenths of a gallon without issue. The boil is about to begin!

  • alcaponejunior  On October 7, 2012 at 3:56 pm

    Damnit, the filter spilled while I was pouring into the fermentation bucket. It won’t be as filtered as I wanted. But then I’ve done multiple batches without filtering the hops, and they came out fine. Oh well.

  • alcaponejunior  On October 31, 2012 at 9:20 am

    Dry hopped today with 2.5oz hallertau

  • alcaponejunior  On November 3, 2012 at 9:44 am

    Bottling today with 98g corn sugar.

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s

%d bloggers like this: